- #Witech Diagnostic Application Download The Application
- #Witech Diagnostic Application How To Register A
- #Witech Diagnostic Application Driver X64 Onto
Witech Diagnostic Application Download The Application
The software connects to StarMOBILE devices, wiTECH VCI Pod and the microPOD II. The Tech2Win application offers all of the features and functions of the Tech 2 for.The wiTECH Diagnostic Application (which includes programming and security functions) is used to interface with Dodge, Chrysler, Jeep and North American Fiat automobiles. The fast will show up next period the is usually used with wiTECH Analysis Application if the user selected US or Europe as the nation during the installation of wiTECH 16.01 and furture variations of wiTECH To download the application, please login to DealerCONNECT > Service > wiTECH Information > microPod Setup UtilityYou can use it to scan your saab tech and scan the diagnostic card.
Witech Diagnostic Application Driver X64 Onto
Then, click “Next” to continue.You are now ready to start the actual installation of the driver. Otherwise, click “Next” to proceed.Read the License Agreement carefully, and accept the terms in the license agreement. Com to download the latest version of the application.Click on “Run” to begin the downloading process of microPOD Setup UtilityThe install wizard will appear to install the wiTECH Driver x64 onto your computer if your PC has not been installed with wiTECH 1.0 application.If the PC has been installed with wiTECH 1.0 App, you will not see the screen below and proceed to Step 6.
Your microPOD II should appear updated and ready for use.With the microPod Setup Utility still running, configure wireless on the wiTECH microPod II device.Guide of wiTECH MicroPod 2 Chrysler diagnostic tool setup.If your dealership purchased a new microPOD and you would like to convert your existing microPOD for using with wiTECH 2.0 System, you need to download and install the microPOD Setup Utility to configure/setup your microPOD for wiTECH 2.0.If you have a restricted network, you must first make sure that all sites listed below are enabled to be able to successfully use microPOD Setup Utility and the wiTECH 2.0 System.Note:Please disable any Anti-Virus software that you have on your computer in order to allow the microPOD Setup Utility to install and run properly.I was ready to connect the wiTECH2 Micropod 2 interface to diagnose Chrysler 300M, but after i connected the adapter with laptop, the MicroPod2 indicator light flashed and software prompted error message “microprocessor 1 is unresponsive”. It is normal activity for the microPOD II to reboot.Click “OK” and you will be navigated back to the wiTECH 2.0 discovery page. Once updating, do not interrupt your microPOD II at any point until the update is complete.*NOTE: This can take upwards of 9 minutes.
Please use the default software CD in package.Please follow the correct steps to connect the micropod2Connect wiTech Micropod2 to vehicle firstIf the red indicator light turn on, then connect wiTech to laptopOpen wiTech software (if software detect newer wiTech version,it will run an upgrade.Wait the upgrade completed. I.e SP271-C wiTech software can work with SP271-C Micropod II firmware. Software cannot be mixed used.
Witech Diagnostic Application How To Register A
Right click Witech Diagnostic Application-> Properties->Open file location2. Please check the knowledgeBase to determine how to register a device"1. You have to send it back to repair.Device with serial number*** is not registered. MUST CONNCT THE DEVICE TO VEHICLE.If the red indicator flashes, the firmware is damaged.
(Very important!!!)If it still display message" an internal registration error has occurred ", just close this windows to ignore it.Tick off " Offline work" at the left corner of screen, then you don't need to login.Go on using wiTech MicroPod 2 to diagnose or program Chrysler.WiTech Micropod2 red light flashes microprocessor 1 isunresponsive solution:I was ready toconnect thewiTECH2 Micropod 2interface todiagnose Chrysler 300M, but after i connected the adapter with laptop, the MicroPod2 indicator light flashed and software prompted error message “microprocessor1isunresponsive”. Find out "VerificationHash", then the followed "Value", change the first number to any value i.e change 6 to any number between 1-9.Then save the text file. Open app-config text file3.
If it does not prompt to update software to newer version, just run software)If you connect to laptop first (power by USB cable) and run softwareimmediately, software and firmware will automatically synchronous upgradeand thatwill lead to the firmware failure. OpenwiTech software (if softwaredetect newer wiTech version,it will run an upgrade.Wait the upgrade completed. If the red indicator light turn on, then connectwiTech to laptop ConnectwiTech Micropod2to vehicle first I.e SP271-C wiTech software can work with SP271-C Micropod II firmware.Please use the default software CD in package.Please follow the correct steps to connectthemicropod2 Software cannot be mixed used.
0 kommentar(er)
